MEAN-18 UnProtect by Independent (IND)
11913 of 49,068 files
23:55:12
Sorry but this file seems to be missing from our server- Browsers may flag this download as unwanted or malicious. If unsure, scan it with VirusTotal.
-
Last modified Nov 5, 1988 7:20:28 PM
MD5 checksum b9ce259c6f24c33a7b03b8057b45b0f4
Mime type ARC archive data, dynamic LZW
Download M18-UNP2.ARC
Size 3 kB
1988 January 22
- Text / Guides and how-tos
2 items in the archive
- M18-EGA.UNP
- U_READ.ME
1/22/88
*********************
* *
* MEAN-18 UnProtect *
* For EGA Version *
* *
*********************
THIS PATCH IS INTENDED TO BE USED TO ALLOW YOU TO MAKE A BACKUP
COPY OF YOUR SYSTEM DISK TO BE USED IN CASE YOU DAMAGE YOUR
ORIGINAL DISKETTE. This patch will also allow you to run the
program from your hard drive without the need to have your system
disk in drive A:.
The patch works by eliminating the code that tests for known bad
sectors on the original diskette to see if it is the genuine
article or an illegal copy. The code begins with an INT 13 (CD
13 HEX), a DOS BIOS disk service routine followed a few bytes
later by another INT 13 instruction. The program then checks the
returned value for the bit configuration that signifies the bad
sectors and, if all is as expected, continues on with program
execution.
The code that needs to be patched is in the GOLF.EXE file and in
the ARCH.EXE file. It is identical in both files and lies near
the end of each file.
In the following steps, you'll locate the start of the test code
and patch it by replacing it with NOP instructions (HEX 90). The
method described uses the DOS DEBUG utility but Norton's Utility
(NU) works too.
Copy all of the files from the MEAN-18 disk onto a fresh floppy
using the DOS COPY command and place your original diskette out
of harm's way.
Assuming DEBUG is in the A: drive and the floppy containing the
files to be unlocked is in the B: drive , proceed as follows:
A:> DEBUG B:GOLF.EXE (Loads the file GOLF.EXE into memory and
displays the "-" DEBUG prompt. Search
for the beginning of the code to be
patched by typing:)
- S CS:100 FFFF CD 13 (Searches the file for the two byte INT
13 instruction. If all goes well, two
addresses should appear on the screen.
XXXX:019C
XXXX:01A8
♀
XXXX indicates that the numbers
preceeding the ":" vary from system to
system but the numbers following the ":"
are the same on all systems. The next
step is to use the "U" command as
indicated to un-assemble a few bytes in
order to verify your position in the
file)
- U CS:019C (Un-assembles 32 bytes of code. Verify
the following sequence of instructions:
INT 13
JB 01E9
MOV AL,[BX+01FF]
PUSH AX
MOV AX,0201
INT 13
POP AX
JB 01E9
CMP AL,F7
JNZ 01B5
(These are the instructions you'll be
patching out in the following step)
- A CS:019C (This command assembles the new
instructions you enter at the keyboard
into the addresses shown. Beginning at
CS:019C, and for the next 21 bytes,
ending with and including CS:01B0, enter
the no op command "NOP" followed by a
<return> or <enter>. Just hit <enter>
at address XXXX:01B1 to end the assemble
command.)
XXXX:019C NOP <enter>
XXXX:019D NOP <enter>
.
.
.
XXXX:01AE NOP <enter>
XXXX:01AF NOP <enter>
XXXX:01B0 NOP <enter>
XXXX:01B1 <enter>
- D CS:019C (Do a HEX dump and verify that bytes
019C through 01B0 have been set to 90
HEX. If they have, write the patched
file to the disk as follows)
♀
- W (Writes the patched file back to the
disk where it can be run by typing GOLF
just as before but now, it can be run
from any drive, including the hard
drive)
- Q (Quit. Exit back to DOS. This command
can be executed at any "-" DEBUG prompt
if you get lost. No modification will
be made to the file on the disk until
you issue the "W" command.
The process is the same for the ARCH.EXE file but because it is a
different length, the segment address, (XXXX part of the address),
will be different. You should find the first INT 13 instruction
at address XXXX:019C and the second one at XXXX:01A8 as before.
You will again be patching 21 bytes and you will start with 019C
and end with 01B0 as before. After doing the HEX dump starting at
address 019C, you again write the file back to the disk with a "W"
command then "Q" uit.
Norton's utilities can also be used to make this patch. Begin by
searcing the GOLF.EXE or ARCH.EXE files for the two byte
combination CD 13 (remember to enter these as HEX bytes). Once
located, change the 21 bytes, starting with the first "CD" byte,
to 90 (a NOP instruction). As a check that you are in the right
place, the byte sequence in both files is CD 13 72 49 8A 87 FF 01
50 B8 01 02 CD 13 58 72 3C 3C F7 75 04. After modifying the
bytes, write the modified file back to the disk. It can then be
run from any drive.
Remember to work only with a copy of your system disk. DEBUG and
NORTON's are great tools but they can really mess you up if you're
not careful. Remember too, that pirating software is just plain
stealing. This patch is for convenience, not proliferation of
pirated copies. Use it in the spirit it was intended.
→♀